20240613解决飞凌的OK3588-C的核心板的适配以太网RTL8211F-CG

news2025/7/12 7:33:20

20240613解决飞凌的OK3588-C的核心板的适配以太网RTL8211F-CG
2024/6/13 16:58


缘起:对于飞凌的OK3588-C的核心板,参照飞凌的底板/开发板。
ETH0空接,ETH1由RTL8211FSI-CG【20¥】更换为RTL8211F-CG【4¥】。
都是千兆网卡,八成是成本的原因。^_

&gmac0 {
    /* Use rgmii-rxid mode to disable rx delay inside Soc */
    phy-mode = "rgmii-rxid";
    clock_in_out = "output";

    snps,reset-gpio = <&gpio0 RK_PB0 GPIO_ACTIVE_LOW>;
    snps,reset-active-low;
    /* Reset time is 20ms, 100ms for rtl8211f */
    snps,reset-delays-us = <0 20000 100000>;

    pinctrl-names = "default";
    pinctrl-0 = <&gmac0_miim
             &gmac0_tx_bus2
             &gmac0_rx_bus2
             &gmac0_rgmii_clk
             &gmac0_rgmii_bus>;

    tx_delay = <0x44>;
    /* rx_delay = <0x4f>; */

    phy-handle = <&rgmii_phy0>;
    status = "okay";
};


修改成为:
&gmac0 {
    /* Use rgmii-rxid mode to disable rx delay inside Soc */
    phy-mode = "rgmii-rxid";
    clock_in_out = "output";

    snps,reset-gpio = <&gpio0 RK_PB0 GPIO_ACTIVE_LOW>;
    snps,reset-active-low;
    /* Reset time is 20ms, 100ms for rtl8211f */
    snps,reset-delays-us = <0 20000 100000>;

    pinctrl-names = "default";
    pinctrl-0 = <&gmac0_miim
             &gmac0_tx_bus2
             &gmac0_rx_bus2
             &gmac0_rgmii_clk
             &gmac0_rgmii_bus>;

    tx_delay = <0x44>;
    /* rx_delay = <0x4f>; */

    phy-handle = <&rgmii_phy0>;
    status = "disabled";
};

&gmac1 {
    /* Use rgmii-rxid mode to disable rx delay inside Soc */
    phy-mode = "rgmii-rxid";
    clock_in_out = "output";

    snps,reset-gpio = <&gpio1 RK_PB4 GPIO_ACTIVE_LOW>;
    snps,reset-active-low;
    /* Reset time is 20ms, 100ms for rtl8211f */
    snps,reset-delays-us = <0 20000 100000>;

    pinctrl-names = "default";
    pinctrl-0 = <&gmac1_miim
             &gmac1_tx_bus2
             &gmac1_rx_bus2
             &gmac1_rgmii_clk
             &gmac1_rgmii_bus>;

    tx_delay = <0x44>;
    /* rx_delay = <0x4f>; */

    phy-handle = <&rgmii_phy1>;
    status = "okay";
};


测试步骤:
台式机/笔记本电脑可以通过WIFI上外网。但是不要再192.168.0.X网段。
由于飞凌的OK3588-C的核心板启动之后,默认IP地址配置为192.168.0.232。
在台式机的以太网卡/笔记本电脑如果没有以太网卡,可以接USB转RJ45网卡。

台式机的IP地址参考配置为:
192.168.0.8
255.255.255.0


Microsoft Windows [版本 10.0.22621.3296]
(c) Microsoft Corporation。保留所有权利。

C:\Users\QQ>ipconfig

Windows IP 配置


无线局域网适配器 本地连接* 1:

   媒体状态  . . . . . . . . . . . . : 媒体已断开连接
   连接特定的 DNS 后缀 . . . . . . . :

无线局域网适配器 本地连接* 2:

   媒体状态  . . . . . . . . . . . . : 媒体已断开连接
   连接特定的 DNS 后缀 . . . . . . . :

无线局域网适配器 WLAN:

   连接特定的 DNS 后缀 . . . . . . . :
   本地链接 IPv6 地址. . . . . . . . : fe80::1a87:11f5:2a01:fb0d%11
   IPv4 地址 . . . . . . . . . . . . : 192.168.3.97
   子网掩码  . . . . . . . . . . . . : 255.255.255.0
   默认网关. . . . . . . . . . . . . : 192.168.3.1

以太网适配器 以太网:

   连接特定的 DNS 后缀 . . . . . . . :
   本地链接 IPv6 地址. . . . . . . . : fe80::acf:748:65e2:32a6%16
   IPv4 地址 . . . . . . . . . . . . : 192.168.0.88
   子网掩码  . . . . . . . . . . . . : 255.255.255.0

   默认网关. . . . . . . . . . . . . :

以太网适配器 蓝牙网络连接:

   媒体状态  . . . . . . . . . . . . : 媒体已断开连接
   连接特定的 DNS 后缀 . . . . . . . :

C:\Users\QQ>


root@ok3588:/# ifconfig
eth0      Link encap:Ethernet  HWaddr 2E:FD:E8:A3:28:CB  
          inet addr:192.168.0.232  Bcast:0.0.0.0  Mask:255.255.255.0

          inet6 addr: fe80::2cfd:e8ff:fea3:28cb/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:38 errors:0 dropped:0 overruns:0 frame:0
          TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:3490 (3.4 KiB)  TX bytes:936 (936.0 B)
          Interrupt:79 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:127 errors:0 dropped:0 overruns:0 frame:0
          TX packets:127 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:337918 (329.9 KiB)  TX bytes:337918 (329.9 KiB)

root@ok3588:/# 
root@ok3588:/# cd /etc/network/
root@ok3588:/etc/network# 
root@ok3588:/etc/network# ls -l
total 28
drwxr-xr-x 2 root root 4096 Mar  9  2023 if-down.d
drwxr-xr-x 2 root root 4096 Mar  9  2023 if-post-down.d
drwxr-xr-x 2 root root 4096 Mar  9  2023 if-pre-up.d
drwxr-xr-x 2 root root 4096 Mar  9  2023 if-up.d
-rw-r--r-- 1 root root  130 Jan  1 08:05 interfaces
-rw-r--r-- 1 root root  130 Jan  1 08:06 interfaces.bak1
-rwxr-xr-x 1 root root  846 Mar  9  2023 nfs_check
root@ok3588:/etc/network# cat interfaces
auto lo
iface lo inet loopback

auto eth0
iface eth0 inet static
address 192.168.0.232
netmask 255.255.255.0
gateway 192.168.0.1

root@ok3588:/etc/network#


IP地址配置:
笔记本电脑:
192.168.3.97  WIFI上外网
192.168.0.88  USB转RJ以太网,指定静态IP地址。

开发板:
192.168.0.232  刷机之后飞凌指定的静态IP地址。


互PING的LOG:
开发板PING笔记本电脑:
root@ok3588:/etc/network# 
root@ok3588:/etc/network# 
root@ok3588:/etc/network# ping 192.168.0.88
PING 192.168.0.88 (192.168.0.88) 56(84) bytes of data.
64 bytes from 192.168.0.88: icmp_seq=1 ttl=128 time=1.16 ms
64 bytes from 192.168.0.88: icmp_seq=2 ttl=128 time=1.07 ms
64 bytes from 192.168.0.88: icmp_seq=3 ttl=128 time=1.16 ms
64 bytes from 192.168.0.88: icmp_seq=4 ttl=128 time=1.19 ms
64 bytes from 192.168.0.88: icmp_seq=5 ttl=128 time=1.16 ms
64 bytes from 192.168.0.88: icmp_seq=6 ttl=128 time=1.15 ms
64 bytes from 192.168.0.88: icmp_seq=7 ttl=128 time=1.16 ms
64 bytes from 192.168.0.88: icmp_seq=8 ttl=128 time=1.21 ms
64 bytes from 192.168.0.88: icmp_seq=9 ttl=128 time=1.13 ms
64 bytes from 192.168.0.88: icmp_seq=10 ttl=128 time=1.17 ms
64 bytes from 192.168.0.88: icmp_seq=11 ttl=128 time=1.29 ms
64 bytes from 192.168.0.88: icmp_seq=12 ttl=128 time=1.24 ms
64 bytes from 192.168.0.88: icmp_seq=13 ttl=128 time=1.23 ms
64 bytes from 192.168.0.88: icmp_seq=14 ttl=128 time=1.17 ms
64 bytes from 192.168.0.88: icmp_seq=15 ttl=128 time=1.22 ms
64 bytes from 192.168.0.88: icmp_seq=16 ttl=128 time=1.16 ms
64 bytes from 192.168.0.88: icmp_seq=17 ttl=128 time=1.15 ms
64 bytes from 192.168.0.88: icmp_seq=18 ttl=128 time=1.15 ms
64 bytes from 192.168.0.88: icmp_seq=19 ttl=128 time=1.30 ms
64 bytes from 192.168.0.88: icmp_seq=20 ttl=128 time=1.21 ms
64 bytes from 192.168.0.88: icmp_seq=21 ttl=128 time=1.20 ms
64 bytes from 192.168.0.88: icmp_seq=22 ttl=128 time=1.23 ms
64 bytes from 192.168.0.88: icmp_seq=23 ttl=128 time=1.22 ms
64 bytes from 192.168.0.88: icmp_seq=24 ttl=128 time=1.17 ms
64 bytes from 192.168.0.88: icmp_seq=25 ttl=128 time=1.19 ms
64 bytes from 192.168.0.88: icmp_seq=26 ttl=128 time=1.17 ms
64 bytes from 192.168.0.88: icmp_seq=27 ttl=128 time=1.24 ms
64 bytes from 192.168.0.88: icmp_seq=28 ttl=128 time=1.24 ms
64 bytes from 192.168.0.88: icmp_seq=29 ttl=128 time=1.18 ms
64 bytes from 192.168.0.88: icmp_seq=30 ttl=128 time=1.21 ms
64 bytes from 192.168.0.88: icmp_seq=31 ttl=128 time=1.25 ms
64 bytes from 192.168.0.88: icmp_seq=32 ttl=128 time=1.08 ms
64 bytes from 192.168.0.88: icmp_seq=33 ttl=128 time=1.28 ms
64 bytes from 192.168.0.88: icmp_seq=34 ttl=128 time=1.19 ms
64 bytes from 192.168.0.88: icmp_seq=35 ttl=128 time=1.16 ms
64 bytes from 192.168.0.88: icmp_seq=36 ttl=128 time=1.15 ms
64 bytes from 192.168.0.88: icmp_seq=37 ttl=128 time=1.26 ms
64 bytes from 192.168.0.88: icmp_seq=38 ttl=128 time=1.27 ms
64 bytes from 192.168.0.88: icmp_seq=39 ttl=128 time=1.22 ms
64 bytes from 192.168.0.88: icmp_seq=40 ttl=128 time=1.22 ms
64 bytes from 192.168.0.88: icmp_seq=41 ttl=128 time=1.17 ms
64 bytes from 192.168.0.88: icmp_seq=42 ttl=128 time=1.14 ms
64 bytes from 192.168.0.88: icmp_seq=43 ttl=128 time=1.11 ms
64 bytes from 192.168.0.88: icmp_seq=44 ttl=128 time=1.18 ms
64 bytes from 192.168.0.88: icmp_seq=45 ttl=128 time=1.21 ms
64 bytes from 192.168.0.88: icmp_seq=46 ttl=128 time=1.24 ms
64 bytes from 192.168.0.88: icmp_seq=47 ttl=128 time=1.19 ms
64 bytes from 192.168.0.88: icmp_seq=48 ttl=128 time=1.26 ms
64 bytes from 192.168.0.88: icmp_seq=49 ttl=128 time=1.14 ms
64 bytes from 192.168.0.88: icmp_seq=50 ttl=128 time=1.11 ms
64 bytes from 192.168.0.88: icmp_seq=51 ttl=128 time=1.10 ms
64 bytes from 192.168.0.88: icmp_seq=52 ttl=128 time=1.26 ms
64 bytes from 192.168.0.88: icmp_seq=53 ttl=128 time=1.14 ms
64 bytes from 192.168.0.88: icmp_seq=54 ttl=128 time=1.18 ms
^C
--- 192.168.0.88 ping statistics ---
54 packets transmitted, 54 received, 0% packet loss, time 53097ms
rtt min/avg/max/mdev = 1.068/1.188/1.300/0.051 ms
root@ok3588:/etc/network# 


笔记本电脑PING开发板:
Microsoft Windows [版本 10.0.22621.3296]
(c) Microsoft Corporation。保留所有权利。

C:\Users\QQ>ping 192.168.0.232

正在 Ping 192.168.0.232 具有 32 字节的数据:
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64

192.168.0.232 的 Ping 统计信息:
    数据包: 已发送 = 4,已接收 = 4,丢失 = 0 (0% 丢失),
往返行程的估计时间(以毫秒为单位):
    最短 = 1ms,最长 = 1ms,平均 = 1ms

C:\Users\QQ>ping 192.168.0.232 -n 1000

正在 Ping 192.168.0.232 具有 32 字节的数据:
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64
来自 192.168.0.232 的回复: 字节=32 时间=1ms TTL=64

192.168.0.232 的 Ping 统计信息:
    数据包: 已发送 = 68,已接收 = 68,丢失 = 0 (0% 丢失),
往返行程的估计时间(以毫秒为单位):
    最短 = 1ms,最长 = 1ms,平均 = 1ms
Control-C
^C
C:\Users\QQ>

本文来自互联网用户投稿,该文观点仅代表作者本人,不代表本站立场。本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如若转载,请注明出处:http://www.coloradmin.cn/o/1821983.html

如若内容造成侵权/违法违规/事实不符,请联系多彩编程网进行投诉反馈,一经查实,立即删除!

相关文章

快速掌握 Python requests 库发送 JSON 数据的 POST 请求技巧

在现代 Web 开发中&#xff0c;客户端与服务器之间进行数据交换的需求越来越普遍。而在 Python 这个强大的编程语言中&#xff0c;requests 库是一个广泛使用且功能强大的 HTTP 请求库。特别是在进行 API 调用时&#xff0c;发送 POST 请求并附带 JSON 数据是一个非常常见的需求…

【React】useMemo

什么是 useMemo&#xff1f; useMemo 是 React 中的一个 Hook&#xff0c;它可以用来缓存计算结果&#xff0c;并在后续的渲染中重复利用这些计算结果。useMemo 接收两个参数&#xff1a;一个函数和一个依赖数组。当依赖数组中的任何一个值发生变化时&#xff0c;useMemo 会重新…

内网环境实现maven项目打包部署(包括踩坑!!)

内网环境实现maven项目打包部署&#xff08;包括踩坑&#xff01;&#xff01;&#xff09; 由于内网保密项目原因 拿我本地测试 过程&#xff1a; jdk1.8 java环境 maven setting配置加上 <!-- 仓库地址(本地上传到内网环境仓库) --> <localRepository>D:\ma…

flutter开发实战-创建一个微光加载效果

flutter开发实战-创建一个微光加载效果 当加载数据的时候&#xff0c;loading是必不可少的。从用户体验&#xff08;UX&#xff09;的角度来看&#xff0c;最重要的是向用户展示加载正在进行。向用户传达数据正在加载的一种流行方法是在与正在加载的内容类型近似的形状上显示带…

Python业务规则引擎库之rules使用详解

概要 在软件开发中,业务规则引擎是一种重要的工具,可以帮助开发者将复杂的业务逻辑从代码中解耦出来,并以更直观的方式进行管理和维护。rules 是一个轻量级的 Python 库,专门用于定义和执行业务规则。它提供了一种简洁且强大的方式来管理应用程序中的规则逻辑,使代码更加…

【Redis】安装和命令行客户端

https://www.bilibili.com/video/BV1cr4y1671t https://www.oz6.cn/articles/58 redis 非结构化有&#xff1a; 键值类型(Redis)文档类型(MongoDB)列类型(HBase)Graph:类型(Neo4j) 扩展性&#xff1a;水平即为分布式扩展 redis特征 键值&#xff08;key-value&#xff09;型…

代码签名证书的申请途径和应用场景

代码签名证书是一种安全技术&#xff0c;主要用于确保软件的完整性和来源的真实性&#xff0c;防止软件在分发过程中被篡改或植入恶意代码。它通过数字签名的方式为软件或代码提供验证&#xff0c;使得终端用户可以确信他们下载的软件确实来自声称的开发者&#xff0c;并且未被…

VMware Ubuntu 虚拟机网卡消失及解决办法

VMware Ubuntu 虚拟机网卡消失 描述原因查找解决方法 描述 在正常使用过程中重启后发现 VMware Ubuntu 虚拟机中的网卡消失了&#xff0c;使用 ifconfig 查看只能看到本地回环&#xff1a; 原因查找 使用如下命令查看是否和我这边遇到的问题一致的原因。 sudo lshw -c netwo…

mathematical-expression-cpp | C++ 数学表达式解析库

数学表达式-cpp Switch to English Document 介绍 本框架是一种针对数学公式解析的有效工具&#xff0c;能够通过C的API解析包含嵌套函数&#xff0c;包含函数&#xff0c;数列步长累加等数学公式&#xff0c;返回值是一个数值的结果对象&#xff0c;同时也可以进行比较运算…

Android面试题之ActivityManagerService的启动流程

本文首发于公众号“AntDream”&#xff0c;欢迎微信搜索“AntDream”或扫描文章底部二维码关注&#xff0c;和我一起每天进步一点点 SystemServer启动 创建SystemContex 用于加载系统相关的资源&#xff0c;比如theme&#xff0c;android命名空间下的资源等创建引导服务&#…

新创作活动,The Sandbox 宣布第二届 “创作者挑战”!

是时候展示你的实力了&#xff01; 继首届 “创作者挑战” 成功举办之后&#xff0c;The Sandbox 很高兴推出第二届 "创作者挑战"&#xff0c;邀请创作者再次释放他们的创造力和创业精神。本次活动从 2024 年 6 月 24 日开始至 8 月 26 日结束&#xff0c;为期 10 …

基于QT5.12.7的VTK8.2下的VS2015 X64源码编译以及测试

有一段时间没更新博客了&#xff0c;最近在考虑使用VTK作为软件的后处理显示&#xff0c;相比于OSG&#xff0c;VTK在后处理上集成了很多优秀的算法&#xff0c;使用起来比较方便&#xff0c;而且后处理一般不需要太多的交互&#xff0c;所以VTK是一个不错的选择。 之前对VTK了…

ansible安装wordpress

1.回顾 yum安装wordpress 查看别名 [rootlocalhost ~]# type ll ll 是 ls -l --colorauto 的别名设置别名 aliasyum install -y alias ymyum install -y# 使用别名 ym nginx# 取消别名 unalias ym# 基于LNMP做一个wordpressnginx mysql 5.7 PHP 7.4#1、初始化过程 修改主机名…

云原生化有什么特点?

云原生化&#xff0c;作为一种先进的构建和管理应用程序的方式&#xff0c;不仅代表着技术的革新&#xff0c;更是云计算时代下的必然产物。其核心目标在于充分发掘并发挥云计算平台的各项优势&#xff0c;使应用程序在性能、弹性、可靠性和安全性等方面达到前所未有的高度。 它…

LeetCode | 171.Excel表列序号

这道题涉及到字符串和进制转换&#xff0c;首先我们先创建一个A-Z到1-26的map映射&#xff0c;方便我们后续遍历字符串转换&#xff0c;然后对字符串从后往前遍历&#xff0c;依次加上对应权重&#xff0c;注意越往前的权重越大&#xff0c;要记得对应乘上26的对应方数 class …

​带三维重建和还原的PACS源码 医院PACS系统源码 PACS系统源码医院PACS系统源码 C/S架构 带三维重建和还原​

带三维重建和还原的PACS源码 医院PACS系统源码 PACS系统源码医院PACS系统源码 C/S架构 带三维重建和还原 ​ 主要的任务就是把日常产生的各种医学影像&#xff08;包括核磁&#xff0c;CT&#xff0c;超声&#xff0c;各种X光机&#xff0c;各种红外仪、显微仪等设备产生的图…

【数组】【快慢双指针】删除有序数组中的重复项+移除元素+删除有序数组中的重复项II

今天趁热打铁&#xff0c;接着刷了几道标签是【数组】的题&#xff0c;基本都是双指针就能解决。 1、删除有序数组中的重复项 该题对应力扣网址 class Solution { public:int removeDuplicates(vector<int>& nums) {int i,j;int count 0;int n nums.size();nums.…

智慧消防新篇章:可视化数据分析平台引领未来

一、什么是智慧消防可视化数据分析平台&#xff1f; 智慧消防可视化数据分析平台&#xff0c;运用大数据、云计算、物联网等先进技术&#xff0c;将消防信息以直观、易懂的图形化方式展示出来。它不仅能够实时监控消防设备的运行状态&#xff0c;还能对火灾风险进行预测和评估…

手把手教你部署并使用国产开源大模型ChatGLM3-6B

前言 部署一个自己的大模型&#xff0c;没事的时候玩两下&#xff0c;这可能是很多技术同学想做但又迟迟没下手的事情&#xff0c;没下手的原因很可能是成本太高&#xff0c;近万元的RTX3090显卡&#xff0c;想想都肉疼&#xff0c;又或者官方的部署说明过于简单&#xff0c;安…

php遇到的问题

1、 underfined at line 3 in xxx.php , 错误提示&#xff0c;注释这行代码 // error_reporting(DEBUG ? E_ALL : 0); 目录&#xff1a;config/config.php